Tools

This dual-sided brush is specifically designed for cleaning hard-to-reach areas of the bicycle drivetrain. The long, stiff bristles of the GSC-3 are narrow enough to reach between the gears of tightly-spaced modern cassettes, while the slim contoured end is capable of picking grit and grime out of tight spaces such as derailleur pulley wheels.

A precision CNC-machined aluminum tool for the installation and removal of select threaded bottom brackets with 16-notch tool fittings, including Wheels Mfg™ Thread Together & FSA® MegaEvo®. Manufactured in-house by Park Tool, anodized for easy identification, and featuring a ratchet/torque wrench-compatible 3/8" drive. Fits 16-notch bottom bracket tool fittings with a major diameter of 48–50 mm and a minor diameter of 46.4 mm, including: - FSA® MegaEvo® - Wheels Mfg™ Thread Together Note: Does not fit Hope™ BSA30

Refill pack for the Park Tool TPT-1 Tubeless Plug Tire Tool and other similar tools. These vulcanized rubber plugs are used to temporarily repair punctures in tubeless bicycle tire systems. Set of 5. NOTE: Intended for tubeless bicycle tires using sealant only. Not compatible with inner tube systems.

The Park FR-6 Freewheel Remover fits most 4-notch BMX and singlespeed freewheels. It can be held with a wrench or vise and its narrow profile allows use without removal of cones and locknuts.

Park's Crank and Bottom Bracket Wrench is perfect for working on old-style bottom brackets. The HCW-4 utilizes a 36mm box-end head and a pin spanner for your bottom bracket removal and installation needs.

Park Tool's Utility Pick Set is a set of three unique, multi-purpose picks ideal for a wide variety of detail work. Features: • Aluminum handle with magnet • Picks are replaceable, cold formed, heat treated and polished high carbon steel • Set includes 1-straight, 1-hook and 1-90 degree pick

Many bicycles will not shift or track properly because the front and rear wheels are not in line with the frame. If these conditions still exist after wheel and derailleur adjustments, the seat stays, chain stays, and rear drop outs of the frame may be misaligned. For years the accepted method to check the alignment of the rear drop-out was to run a string on either side. This method does work to some extent. However, it is not accurate because the measurement is not taken at the drop-out. With the Park Tool Frame Alignment Gauge, the alignment can be checked quickly and accurately at the drop-out. It includes a retractable pointer to fit all sizes and types of bicycles.

- Used when facing BB86/92 bottom bracket shells and reaming is not required - Used in conjunction with HTR-1 head tube reaming and facing set (PK-6710), 750.2 centering cone adapter (PK-6735) and 690-XL facing cutter (PK-6730)

The MT-10, 20, 30 and 40 are high quality folding take-along tools that feature forged aluminum side plates, a mix of hardened and plated tools, and smooth ergonomic operation.

Choose the perfect tool for the job with Park's P-Handled Hex Wrenches. These top-shelf Allen wrenches come with offset handles made from durable nylon in a comfortable, ergonomic design. They are made of chrome vanadium for exceptional durability. The long shafts feature Bondhus heads for accessing hard-to-reach bolts and the short ends are chamfered for extra grip and high-torque applications.

Designed and built specifically for a wide variety of bicycle Torx compatible work, the THT-1 is a set of eight common sizes of professional quality T-Handle star-shaped wrenches built for speed, efficiency, leverage and a perfect fit. Soon to become your favorite Torx compatible set, the THT-1 includes a handy tool holder that mounts to any vertical surface, including pegboard and solid surfaces (fasteners not included). - Carefully selected combination of Chrome Vanadium and S-2 tool steels - T6, T8, T10, T15, T20, T25, T30 and T40 Torx compatible wrenches included - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Sliding T-handle creates increased leverage and multiple access positions - Tool holder is included with the set and mounts to any wall, bench or tool box, perfectly positioning each wrench for easy access and storage

Designed and built specifically for a wide variety of bicycle hex work the THH-1 is a set of eight common sizes of professional quality T-Handle hex wrenches built for speed, efficiency, leverage and a perfect fit. Soon to become your favorite hex set, the THH-1 includes a handy tool holder that mounts to any vertical surface, including pegboard and solid surfaces (fasteners not included). - Carefully selected combination of Chrome Vanadium and S-2 tool steels - 2, 2.5, 3, 4, 5, 6, 8 and 10mm hex wrenches included - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Machined, chamfered tips allow easier insertion into hex fittings - Integrated “Strip-Gripper” twisted hex that makes removal of most bolts with stripped or over-sized hexes fast and easy - Sliding T-handle creates increased leverage and multiple access positions - Tool holder is included with the set and mounts to any wall, bench or tool box, perfectly positioning each wrench for easy access and storage

Professional quality T-Handle hex wrench built for speed, efficiency, leverage and a perfect fit. - Carefully selected combination of Chrome Vanadium and S-2 tool steels - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Machined, chamfered tips allow easier insertion into hex fittings - Integrated “Strip-Gripper” twisted hex that makes removal of most bolts with stripped or oversized hexes fast and easy - Sliding T-handle creates increased leverage and multiple access positions

Precisely machined for a perfect fit, this 8-notch tool removes and installs the lockring that retains front chainrings found on Bosch Gen 2 e-bike motors after the crank arm is removed. - Fits Bosch Active Line (chainrings less than 20 teeth), Performance Line and Performance Line CX models - For lockrings with 50mm outside diameter and 8 notches - Replacement for Bosch 0275009003 tool - Torque wrench compatible 3/8-inch square drive - Constructed of 4140 heat treated steel and plated for long life

The QTH-1 is an ergonomic T-handled bit driver equipped with eight common bits to fit a wide variety of fasteners and fittings found on bicycles. The magnetic "quick-change" handle allows for one-handed operation and makes changing bits quick and easy. The bit holder can be magnetically attached to any magnetic surface such as a repair stand or tool box, or can be permanently mounted to any wall or tool board. The QTH-1 is a professional-grade tool built to withstand the rigors of daily shop use and is fully rebuildable. Includes the following magnetic 1/4" bits: - 2mm, 2.5mm, 3mm, 4mm, 5mm & 6mm hex - T25 Torx-compatible - #2 Philips cross tip - Bit holder includes empty spaces for 2 extra bits

Park's Crank and Bottom Bracket Wrench is perfect for working on old-style bottom brackets. The HCW-5 is a dual-sided lockring hook spanner, featuring a three-prong side and a single hook side for different style lockrings.

The BBT-16 removes and installs the self-extracting/one-key release caps on SRAM and RaceFace cranks with a 16mm hex hole. Features investment cast steel construction and an option to use 8mm hex for better leverage.

World-famous Park Tool quality wrapped up in a great set of metric combination wrenches. Forged from chrome vanadium steel, chrome plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip.

Park's Offset Brake Wrench utilizes a unique design that allows it to reach into tight areas that other wrenches cannot. The OBW-3 features a 14mm wrench on one end and the other end fits into a brake's tension springs to rotate the brake around its bolt for proper alignment. The OBW-4 features 10-, 11-, 12-, and 13-mm opening to fit most models of sidepull brakes.

The Park FR-2 Freewheel Remover fits SunTour two-notch freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel. (Not recommended for use with SunTour 4- and 6-notch freewheels.)

Park Tool's 692 Left-Hand Bottom Bracket Tap is a 1.370" x 24 TPI replacement tap for the BTS-1 Bottom Bracket Tap Set. This tap is used on the drive side (right side) of the bike. This side of the bottom bracket uses a counter-clockwise or left-hand thread. Note: It is very important to have sharp and accurate cutting tools for effective tapping and thread-chasing. Using an excessively worn or damaged tap can cause permanent damage to the frame and/or bottom bracket.

- Precision tool for quickly and easily removing the headset crown race from the crown race seat of the fork - Fully adjustable, allowing precise, independent positioning of each blade around the crown race for flexibility in fitting around crown race interferences - Works with 1,1-1/8,1-1/4,1.5" forks (suspension or rigid) and crown races with outside diameters up to 64mm - Accepts steerers up to 430mm - All steel construction for long life

- Used to ream and face BB86/92 bottom bracket shells to an ID of 40.98mm - Used in conjunction with HTR-1 head tube reaming and facing set (PK-6710), 750.2 centering cone adapter (PK-6735) and 690-XL facing cutter (PK-6730)

Designed and built with the specific needs of the bike mechanic in mind. The RP-SET.2 includes five professional quality pliers for internal snap rings and one for external snap rings. Pliers are made from forged, heat treated cro-moly steel with a return spring and vinyl dipped grips. RP-1: .9mm straight internal. Opens from 22mm down to 0 (tips touching) RP-2: 1.3mm bent internal. Opens from 22mm down to 2mm (center to center) RP-3: 1.3mm bent external. Opens from 2mm (center to center) up to 18mm RP-4: 1.7mm bent internal. Opens from 21mm down to 2mm (center to center) RP-5: 1.7mm straight internal; Opens from 25mm down to 0 (tips touching)

The Park FR-4 Freewheel Remover fits Atom, Regina, splined Zeus and some Schwinn-approved freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.

Having trouble getting at internal spoke nipples? Park's Square Socket Internal Nipple Spoke Wrench comes to your rescue. The extra-long socket fits recessed nipples on most deep-section aero wheels. And, the ergonomic handle is comfortable even after you've built wheels for the entire team.

Park's Fixed-Gear Lockring Wrench features 2 different radius hooked spanners for a precise fit, and easy removal and tightening of most fixed-gear lockrings. The HCW-17 fits rings with an outside diameter of 41 to 44mm. It also fits BMX cassette hub lockrings with external notches.

A clean bike is a happy bike! Park Tool's Bike Cleaning Brush Kit is a four-piece brush set designed specifically to clean bicycles. Ergonomically designed and featuring dual-density, sure-grip handles, the BCB-4.2 kit includes: • 1 GSC-1 Gear Clean Brush • 1 Tapered Detail Brush • 1 Frame Cleaning Sponge/Bristle Brush • 1 Soft Bristle Soaping Brush

Dial Indicator Set bolts directly to the DT-3 allowing for greater accuracy and a way to measure results. Now includes an elongated, cylindrical tip that is large enough to work around voids in most rotors.

A fast and convenient tool to remove and install 12-spline Shimano/SRAM style cassette lockrings, as well as similar lockrings on rotor discs. The FR-5H features a modified FR-5 tool that allows use without removing most quick release skewer nuts. The removable, threaded steel handle makes it possible to replace a worn or damaged head. - Fits Shimano, SRAM (including 1x), SunRace, SunTour, Chris King and other cassette lockrings - Also fits some Shimano disc brake lockrings